Ring Indoor Cam Gen 2 Mount: Adhesive or Screw-In?

The choice is the surface, not the bracket

With the Brainwavz Screwless Wall Mount for Ring Indoor Cam (GEN 2), you are not choosing between two products. You get one tilted holder that supports both a peel-and-stick adhesive fixing and a screw-in fixing, with hardware supplied. The real comparison is between the wall you want to use and the method that wall can take.

Compatibility is the first filter. The holder is designed for the Generation 2 Ring Indoor Cam only, so owners of other Ring models should stop here rather than adapt it.

What the mount gives you either way

• Screwless Wall Mount for Ring Indoor Cam (GEN 2), Easy to Install, No Mess, Strong Adhesive Holder with Screw In Option: Designed for Ring Indoor Cam Gen 2 only, with a push-fit base and a rear overhang that holds the camera in place. Both fixing methods share the same holder, so camera fit and retention do not change with your choice.

  

• Screwless Wall Mount for Ring Indoor Cam (GEN 2), Easy to Install, No Mess, Strong Adhesive Holder with Screw In Option: The tilted design mounts the camera on a vertical surface for a better viewing angle and improved room coverage. Placement, not fixing method, is what determines whether the angle actually helps.
• Screwless Wall Mount for Ring Indoor Cam (GEN 2), Easy to Install, No Mess, Strong Adhesive Holder with Screw In Option: The power cable exits through an access hole at the rear of the hanger. Cable routing is built in, so you do not need to choose between methods based on cable management.

Adhesive versus screw-in on this holder

The catalog describes both methods but does not state load ratings, cure times beyond letting the tape set for a few hours, or which method holds better on a given wall. Treat the points below as what the supplied information supports, not a strength ranking.

• Screwless adhesive fixing: Peel off the red backing, press the tape onto the desired spot, and let it set for a few hours before use. No screws or tools are needed. The catalog explicitly rules out painted, damp and plastered walls.
• Screw-in fixing: All hardware is included: screws, washers, wall plugs and screw caps. The catalog states the mount can be screwed into walls and wood surfaces, which makes this the option for the surfaces the adhesive cannot take.
• What stays the same: The tilted angle, push-fit camera retention and rear cable exit apply to both methods. Your decision only changes how the holder attaches to the wall.

Check the wall before you pick a method

• Painted wall: Do not use the adhesive here. The catalog lists painted surfaces as unsuitable for adhesive mounting, so plan on the screw hardware instead.
• Damp wall: Also excluded from adhesive use. Moisture-prone spots are not suitable surfaces for the tape, per the supplied notes.
• Plastered wall: The third excluded surface. Again, the screw option is the route the catalog leaves open.
• Wood surface: The catalog states the mount can be screwed into wood, and does not list wood among the adhesive exclusions.
• Plain vertical wall you can drill: Either method is described as possible, so choose based on whether you want to avoid drilling rather than on camera performance.

Install in the order the evidence supports

1. 1. Confirm the camera: Check you have the Ring Indoor Cam Gen 2. The holder is not described as fitting other generations.
2. 2. Choose the fixing: Adhesive only on surfaces the catalog permits; screw hardware for painted, damp or plastered walls and for wood.
3. 3. Fix the holder: For adhesive, peel the red backing and stick it in place, then let it set for a few hours. For screws, use the supplied screws, washers, wall plugs and screw caps.
4. 4. Route the cable: Feed the power cable through the rear access hole.
5. 5. Seat the camera: Push-fit the camera into the base so the rear overhang holds it secure.

Where the comparison runs out

The supplied information does not include a weight limit for the adhesive, a required screw size or drill bit, or guidance on removing the mount later. It also does not confirm performance on materials beyond the surfaces named. If your wall is brick, tile or something else not mentioned, the catalog neither approves nor rules it out, so check the surface yourself before committing.

One honest trade-off is worth stating plainly: the screwless option is the faster, no-mess path, but it is the more restricted one. The screw option takes more work and leaves holes, yet it covers the exact surfaces the adhesive cannot. If your wall is painted, damp or plastered, the decision is already made for you.