Kasa Spot KC100 Corner Mount: No-Screw Adhesive Install

By Brainwavz Audio | Published: 2026-10-31

Category: How-to Guides

Mount your Kasa Spot KC100, KC105 or EC60 in a corner without drilling. Follow these steps to prep the surface, apply the 3M VHB adhesive holder and check the fit.

Quick answer

Use the adhesive corner mount made for the Kasa Spot KC100, KC105 and EC60, clean the corner surface, peel the 3M VHB tape and press the holder firmly in place. No screws are needed, but the bracket only fits those Kasa Spot models.

Why a corner mount changes camera coverage

A corner position gives a Kasa Spot a wider view of a room or entryway than a flat wall in many layouts, because the camera sits at the junction of two walls. The trade-off is that the mount must sit flush against both surfaces, so a purpose-made corner bracket is easier to align than a flat adhesive plate.

Adhesive mounting also keeps the install reversible: you avoid drilling into tile, painted drywall or rental walls. The limitation is that the bond is only as good as the surface and the prep, which is why the steps below focus on cleaning and pressing rather than speed.

When adhesive is the wrong choice

Skip the adhesive route if the corner is textured brick, loose plaster, damp or dusty, because 3M VHB tape needs a clean, sound surface to hold. If you need to reposition the camera often, a screw-fixed bracket is more forgiving than peeling and re-sticking tape.

Also confirm the camera model before buying: this holder is listed for the Kasa Spot KC100, KC105 and EC60 only, and the catalog states it will not fit other brands or models.

Step-by-step adhesive corner mount install

Confirm your camera model: Check the label on your Kasa Spot and match it to KC100, KC105 or EC60 before opening the pack. Common mistake: assuming any Kasa camera fits, when the catalog states this bracket will not fit other brands or models. Snap a photo of the model label before installing so you can verify fit later.
Choose and clean the corner: Pick a corner within reach of a power source and wipe both wall faces with a dry or slightly damp cloth, then let them dry fully. Common mistake: sticking the holder onto dusty, greasy or freshly painted surfaces, which weakens the 3M VHB bond. Avoid corners above heat sources or in direct steam, since moisture and heat stress adhesive over time.
Test-fit the holder before peeling: Hold the bracket in the corner and check that the camera will point where you want it, with no shelf or cabinet blocking the view. Common mistake: peeling the safety tape first and then discovering the angle is wrong. Mark the top edge lightly with painter's tape if you need a reference for re-placement.
Peel and press the 3M VHB tape: Remove the safety tape from the back of the holder, press it firmly into the corner and hold for about 30 seconds, applying pressure across the whole pad. Common mistake: pressing only the center, which leaves the edges lifting. Let the adhesive sit before hanging the camera if your surface is cool or slightly uneven.
Seat the camera and check the view: Clip the Kasa Spot into the holder, adjust the angle and open the app to confirm the corner view covers the area you need. Common mistake: tightening or forcing the camera before the bracket is fully seated. If the view is wrong, adjust the camera angle first rather than peeling the mount off.
Know the removal rule: If you must remove the holder, peel slowly from one edge rather than pulling straight out, and expect the tape to be single-use. Common mistake: reusing stretched VHB tape, which will not hold as well the second time. Keep the second mount from the 2 pack as your replacement rather than reusing old tape.

Product facts

Corner Wall Mount for Kasa Spot KC100, KC105, EC60 (2 Pack) Security Camera - Adhesive Holder, No Hassle Bracket, Strong 3M VHB Tape, No Screws, No Mess Install: Corner wall mount designed specifically for TP-Link Kasa Spot KC100, KC105 and EC60 cameras, supplied as a 2 pack with 3M VHB tape and no screws. The model-specific fit means you should check your camera label first, and the two-pack lets you cover two corners or keep a spare.
Corner Wall Mount for Kasa Spot KC100, KC105, EC60 (2 Pack) Security Camera - Adhesive Holder, No Hassle Bracket, Strong 3M VHB Tape, No Screws, No Mess Install